iPhone 13 - Replacing the earpiece

Before repairing, we recommend that you use our checklist to test the basic functions of your iPhone 13. This way you can check afterwards if your repair was successful.

1. Press and hold the side and volume down key simultaneously for a few seconds.
2. Wipe the displayed slider from left to right.

• 2 × 6.8 mm Pentalobe

Once you open your iPhone its specified IP68 certification will expire.

We recommend using a screw storage to keep all disassembled parts and screws safe and organized. Our magnetic pad has the additional advantage that nothing can move on it.

1. Unscrew the two Pentalobe screws left and right of the Lightning connector.
2. Then put them into a screw storage.

The screen of the iPhone 13 is heavily glued. In order to remove it, you first have to heat the adhesive sufficiently with hot air. For this, use a hot air device, such as a hot air dryer or an ordinary hair dryer.

1. Run a hot air device evenly over the edge of the screen.

We recommend a flat pick to insert between the screen and the case unit. Alternatively, the iPlastix and iFlex can be helpful as well.

1. Attach a suction cup to the lower edge of the screen and pull it firmly upwards to create a narrow gap between the screen and the case unit.
2. Insert a flat, stable tool into the gap to enlarge it.

Do not insert your tool too far on the side of the volume buttons to avoid damaging any cables inside the device.
Be careful not to open the screen too far while the sensitive screen cables are still attached.

1. Move the plastic tool once around the edge of the screen. Press it upwards at the same time to release its hooked lugs from the case unit.
2. When the screen is completely detached, you can carefully unfold it towards the volume buttons. Lean it against a stable object.

• 4 × 1.2 mm Phillips
• 1 × 1.7 mm Y-Type
• 1 × 1.6 mm Phillips

To remove the screen completely, you have to detach the battery connector as well as the two screen connectors. These are located under two cover plates.

The upper cover plate is hooked on one side.

1. Unscrew the six screws from the two cover plates and put them in your screw storage.
2. Then carefully remove the plates from your device with a pair of tweezers.

• Connector

1. Use a plastic lever tool to move under the connector and carefully separate it from the board. We use a plastic spudger for this.

• Connector

1. Pry the two screen connectors carefully off the logic board with a spudger.
2. Then put the fully detached screen aside.

• Connector

Before you can remove the logic board, you first have to detach all twelve connectors on it. Note that in some cases two connectors are located underneath each other.

1. Carefully separate the connectors from the board with a spudger.

• 1 × 3.3 mm Standoff
• 1 × 1.6 mm Phillips
• 1 × 3.9 mm Standoff

Be careful not to damage any connectors when removing the logic board. It is best to hold them aside with tweezers for this purpose.

1. Loosen the three screws that hold the board in the case.
2. Then carefully take the logic board out of the device.

• 1 × 1.4 mm Phillips
• 1 × 3.6 mm Standoff

1. Remove the two screws of the earpiece.
2. Then take the detached earpiece out of the device.

• 1 × 1.4 mm Phillips
• 1 × 3.6 mm Standoff

Be careful not to mix up the screw lengths. A too long screw in the wrong place may damage the device.

1. Insert the new earpiece and screw it in place.

• 1 × 3.3 mm Standoff
• 1 × 3.9 mm Standoff
• 1 × 1.6 mm Phillips

Make sure not to pinch any connectors when inserting the logic board. It is best to hold them aside with a pair of tweezers.

1. Put the logic board back into the case. Make sure that it sits level.
2. Then fix it again with the three screws.

• Connector

Never press down connectors with force. Damage can lead to the failure of an entire component.Do not connect the battery yet.

1. Reattach all twelve connectors to the logic board by carefully pressing them down. You should hear and feel them click into place.

If the adhesive frame is still in good condition, you do not need to install a new one. However, if it is defective or no longer sticks properly, we recommend replacing it with a new one.

1. Heat up the adhesive frame and pull it off bit by bit with a pair of tweezers.
2. Remove the carrier film of the adhesive frame and press it onto the edge of the case.
3. Then remove the protective film from the upper side of the adhesive frame. The remaining protective film on the edge of the case should only be removed shortly before the end of the repair.

• Connector

1. Lean the screen back against a stable object to connect it.
2. Carefully press the two screen connectors onto the logic board one after the other. You should hear and feel them click into place.

• Connector

Always connect the battery last to avoid a potential short circuit.

1. Carefully press the connector onto the logicboard, so that you can hear and feel it click into place.

Before you close your iPhone 13 for good, we recommend testing the new earpiece as well as other basic functions of your phone. This way, you can make sure that your repair was successful. Again, use our checklist for this.

1. Carefully fold the screen around, but do not press it into the case yet.
2. Turn on your iPhone and call someone.
3. If something does not work properly, check again if everything is installed and attached correctly.

• 4 × 1.2 mm Phillips
• 1 × 1.7 mm Y-Type
• 1 × 1.6 mm Phillips

The upper cover plate is additionally hooked on one side.

1. Position the two cover plates over the connectors. The screw holes help you with the alignment.
2. Screw the cover plates in place. Fix them with tweezers, so that they do not move.

When folding down the screen make sure not to pinch any flex cables.

1. If you have applied a new adhesive frame, peel off the remaining protective film at this point.
2. Flip the screen around and press it firmly into the case frame, so that it sits level all over. You should hear and feel it click into place.
3. Finally, heat the edge of the screen with hot air in order for the adhesive to bond properly again.

• 2 × 6.8 mm Pentalobe

1. Fix the screen by fastening the two rear case screws again.