iPhone 6 Plus speaker repair guide

The speaker won’t play any music

In this guide, we show you how to replace your iPhone 6 Plus’ defective speaker on your own. You need this repair if your phone doesn’t play music or only plays it quietly, or if your ring tone doesn’t play when you get calls.

Required tools

For storing screws

For storing screws

We recommend storing your screws so you don’t mix up the various screws and small parts.
from €10.99 on Amazon
Tweezers

Tweezers

We recommend using tweezers to remove screws and various small parts from your device.
on Amazon
Pick Set

Pick Set

You need a flat but stable tool such as a pick to pry out parts that are glued in place.
from €14.99 on Amazon
Plastic prying tool

Plastic prying tool

You need a flat plastic prying tool to disconnect the various plugs and connectors.
from €14.99 on Amazon
Steel Laboratory Spatula

Steel Laboratory Spatula

You need a flat and sturdy prying tool to disconnect glued parts.
on Amazon
Pentalobe PL1 screwdriver

Pentalobe PL1 screwdriver

You need the right screwdriver for removing pentalobe PL1 screws.
on Amazon
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
from €10.84 on Amazon

Required replacement part

iPhone 6 Plus Speaker

iPhone 6 Plus Speaker

from €10.99 on Amazon

Show all replacement parts for the iPhone 6 Plus

Steps

15 Steps

Turning off your Device

Step 1

Removing the enclosure screws

Step 2

Lifting the display

Step 3

Disconnecting the battery connector

Step 4

Disconnecting the connectors

Step 5

Disconnecting the ribbon cable

Step 6

Removing the vibration motor

Step 7

Removing the speaker

Step 8

Installing the speaker

Step 9

Installing the vibration motor

Step 10

Connecting the cable

Step 11

Connecting the display

Step 12

Installing the battery

Step 13

Attaching the display

Step 14

Fastening the enclosure screws

Step 15

Getting started with the repair of your iPhone 6 Plus

If you get stuck or have questions, you can post a comment. We’d be happy to help.

15 steps

Turning off your Device
Turn your iPhone off completely to avoid damaging it during the repair. Press the standby button for about three seconds until the slider appears.
Wipe it from left to right. Now your iPhone will shut down completely, which can take about ten seconds.
Removing the enclosure screws
You need a pentalobe screwdriver to open the iPhone 6 Plus.

Remove the two pentalobe screws at the bottom of the enclosure. They are located to the right and left of the Lightning connector. Put the screws in the same container.
2 x 3.8 mm pentalobe screw
Lifting the display
Put your iPhone 6 Plus on a soft, clean surface to avoid scratching the back.

To lift the front panel, you need a suction cup and a hard plastic pick. If the screen is severely cracked, cover all of it with packing tape before you continue.

Place the suction cup over the Home button (if possible) or next to it (see figure 1). While lifting the screen with the suction cup, insert the hard plastic pick between the aluminum frame and the display frame and press down the aluminum frame. Also use the hard plastic pick to raise the screen (see figure 2). This usually takes several attempts.

As soon as you can lift the screen a few millimeters, you have to carefully work your way around the outside until it’s loosened on both sides (see figure 3).
Disconnecting the battery connector
Use a Phillips screwdriver to remove the Phillips screws on the battery connector (see figure 1). Then lift the cover (see figure 2). Put all the parts in the same container.
1 x 3.2 mm Phillips screw
1 x 2.3 mm Phillips screw

Now carefully lift the battery connector by inserting the pointed tip of the ESD spudger slightly below the connector (see figure 3). If you don’t have a spudger, you can also try using your fingernail.
Disconnecting the connectors
First remove the five Phillips screws from the silver cover (see figure 1). Put the screws in the same container. Then lift the cover to remove it.
1 x 1.6 mm Phillips screw
3 x 1.2 mm Phillips screw
1 x 2.9 mm Phillips screw

Disconnect the following four overlapping connectors (see figure 2) in the order shown below. Be very careful. Place the pointed tip of the spudger very slightly below the contact and lift it up.
Front camera/sensor/earpiece/ambient microphone
Touch ID cable
LCD
Touchscreen
Disconnecting the ribbon cable
Using the spudger, carefully disconnect the lower oblong connector for the Lightning connector (see figure 1).
Removing the vibration motor
Remove the two screws that hold the vibration motor in place (see figure 1).
2 x 2.3 mm Phillips screw

Carefully disconnect the little antenna connector using the spudger (see figures 2 and 3).

Now carefully move the vibration motor to the side. Pay close attention to the antenna cable routed in the little silver rail along the speaker (see figure 4).

Now turn the vibration motor so you’re looking at the bottom of it. Now you can remove the antenna cable from the little bracket (see figure 5).

Then you can remove the vibration motor.

Removing the speaker
Now remove the following two Phillips screws that hold the speaker in place (see figure 1). Put the screws in different containers so you can easily identify them later.
1 x 2.3 mm Phillips screws
1 x 2.8 mm Phillips screws

Now you can remove the speaker (see figure 2). Make sure you don’t lose the little silver rail (see figure 3).
Installing the speaker
Put the new speaker back in the original position (see figure 1) and fasten the Phillips screws again (see figure 2).
1 x 2.3 mm Phillips screw
1 x 2.8 mm Phillips screw
Installing the vibration motor
Attach the antenna cable to the vibration motor again (see figure 1).

Place the vibration motor at the original location. Make sure you insert the antenna cable properly in the rail against the speaker (see figure 2).

Now reconnect the antenna connector (see figure 3)..

Screw the vibration motor in place again (see figure 4).
2 x 2.3 mm Phillips screw
Connecting the cable
Now connect the connector for the Lightning connector again (see figure 1).
Connecting the display
Reattach the connectors (see figure 1). Connecting the LCD connector generally takes a few tries. Be very careful to avoid bending the connector.
Front camera/sensor/earpiece/ambient microphone
Touch ID cable
LCD
Touchscreen

Start your iPhone as soon as the connectors are securely attached. Check the function of the LCD, touchscreen, proximity sensor, front camera and earpiece.
If the connectors aren’t connected properly, stripes will appear on the display or parts of the touchscreen won’t work.

Now attach the cover and screw it in place (see figure 2).
1 x 1.6 mm Phillips screw
3 x 1.2 mm Phillips screw
1 x 2.9 mm Phillips screw
Installing the battery
Attach new adhesive strips below the battery. Otherwise, the battery will have too much room and move around

Now put the battery back in the iPhone and connect the connector (see figure 1).

Put on the silver cover and screw it in place (see figure 2).
1 x 3.2 mm Phillips screw
1 x 2.3 mm Phillips screw
Attaching the display
Then carefully fold down the screen. Make sure that the edge on the upper part of the screen where the cables are clicks into place properly. Now carefully push the screen on toward the Home button until it is properly installed in the frame.
Fastening the enclosure screws
Now screw in the two pentalobe screws at the bottom of the enclosure.
2 x 3.8 mm pentalobe screws