The battery of your iPhone SE (2nd generation) discharges much too fast? Is your smartphone having trouble turning on, or is it constantly crashing?

If you recognize yourself here it is time to replace the battery of your iPhone. In order to have full battery power again, we explain you in this photo tutorial step by step how to do this best and safest.

In the photos of the repair instructions the iPhone 8 is shown. However, since it is almost identical in construction to the iPhone SE (2nd generation), we have reused the same photos. All steps to be carried out have also remained the same.

If you follow the steps of our instructions with a little patience, you will be able to replace your battery on your own. Good luck!

Required tools

  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €15.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    from €10.99 on Amazon
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    on Amazon
  • Pick Set

    Pick Set

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    from €14.99 on Amazon
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    from €14.99 on Amazon
  • Pentalobe PL1 screwdriver

    Pentalobe PL1 screwdriver

    You need the right screwdriver for removing pentalobe PL1 screws.

    on Amazon
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    from €10.84 on Amazon
  • Phillips screwdriver with centering pin

    Phillips screwdriver with centering pin

    Phillips screwdriver with practical centering pin for logic board screws.

    on Amazon
  • Y-type Y000 screwdriver

    Y-type Y000 screwdriver

    You need the right screwdriver for removing Y-type screws.

    on Amazon
Show all replacement parts for the iPhone SE (2020) 

Getting started with the repair of your iPhone SE (2020)

If you get stuck or have questions, you can post a comment. We’d be happy to help.

36 steps
  1. Switching off your iPhone SE (2nd generation)

    iPhone SE (2020) - Switching off your iPhone SE (2nd generation) 01
    iPhone SE (2020) - Switching off your iPhone SE (2nd generation) 02
    iPhone SE (2020) - Switching off your iPhone SE (2nd generation) 03
    1. Turn off your iPhone SE (2nd generation) completely in the first step, to protect it from potential damage during repair.
      To do so, keep the standby button pressed until the "Power off" slider appears.
    2. Wipe the slider from left to right. Your iPhone will shut down completely in about ten seconds.
  2. Removing the rear case screws

    iPhone SE (2020) - Removing the rear case screws 01
    iPhone SE (2020) - Removing the rear case screws 02
    Used tools
    Wiha PicoFinish Pentalobe Screwdriver PL1
    Magnetic Pad
    • 2 × 3.4 mm Pentablobe
    1. Remove the two Pentalobe screws to the right and left of the Lightning connector with a Pentalobe screwdriver. Then put the screws in your screw storage box.

    In order not to lose any of the removed parts or screws, we recommend that you use a screw storage box. For example, you can convert an old sewing box into a screw storage box. We use a high-quality magnetic pad on which you can also arrange the components exactly as you found them in your phone. This way you know exactly where each screw has been and makes it much easier for you to assemble it later.

    Used tools
    Wiha PicoFinish Pentalobe Screwdriver PL1
    Magnetic Pad
  3. Heating up the display

    iPhone SE (2020) - Heating up the display 01
    iPhone SE (2020) - Heating up the display 02
    Used tools
    Heat gun
    1. First, place your iPhone SE on a soft, clean surface to prevent scratches when lifting the display.
    2. Since the display is glued to the edge, you will need to heat it up to make it easier to detach from the rest of the case.
      To do this, use a hot air device like a heat gun or alternatively a regular hairdryer to drive evenly over the edge of the display from the outside.

    The rule of thumb for warming up is: you should still be able to touch your device without it becoming unpleasantly hot.

    Used tools
  4. Detaching the display

    iPhone SE (2020) - Detaching the display 01
    iPhone SE (2020) - Detaching the display 02
    iPhone SE (2020) - Detaching the display 03
    Used tools
    Flat Picks
    VAKUPLASTIC Suction Cup

    After opening the iPhone SE (2nd generation) the warranty for protection against dust and splashing water of the IP67 classification expires.

    1. Press the suction cup on the display in the area above the home button and pull it upwards. By lifting the display screen, you create a narrow gap between the aluminium and display frames.

    If the display screen is badly broken, apply parcel tape to it beforehand.

    1. Insert a flat plastic tool into the narrow gap between the aluminium frame and the display frame and try to use it to additionally push the aluminium frame upwards. We use flat plastic picks for this.

    Take care not to insert the picks on the side of the standby button too far, in order not to damage the display's flex cable.

    1. Drive the pick once completely around the display frame. Keep warming the edge of the display and leave individual picks in the frame to prevent the adhesive from rejoining in the areas that have already been loosened.
    Used tools
    VAKUPLASTIC Suction Cup
  5. Opening the display

    iPhone SE (2020) - Opening the display 01
    iPhone SE (2020) - Opening the display 02

    Never open the display more than 180° while it is still connected, otherwise the flex cables may tear.

    1. Now carefully push the display upwards with the plectrum so that the lugs come off the aluminium frame.
    2. Then open it laterally towards the standby button. Lean the display against a stable object to avoid overstretching the flexible cables,
  6. Disconnecting the battery connector

    iPhone SE (2020) - Disconnecting the battery connector 01
    iPhone SE (2020) - Disconnecting the battery connector 02
    iPhone SE (2020) - Disconnecting the battery connector 03
    iPhone SE (2020) - Disconnecting the battery connector 04
    iPhone SE (2020) - Disconnecting the battery connector 05
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 2 × 2.6 mm Phillips
    • 2 × 1.0 mm Phillips
    • Connector

    Disconnect the battery connector immediately at the beginning of the repair. This not only prevents a short circuit, but also ensures that you do not accidentally switch on your phone during the repair.

    We're using photos of iPhone 8 in this guide. The battery connector may look slightly different in iPhone SE (2nd generation), but it's in the same place in the device.

    1. Using a Phillips screwdriver, loosen the four screws of the contact cover and carefully lift it out of your device with tweezers.
    2. Now disconnect the battery contact by carefully sliding a plastic spudger under the plug and lifting it off. We always use a plastic spudger for this.


    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  7. Disconnecting the display connectors

    iPhone SE (2020) - Disconnecting the display connectors 01
    iPhone SE (2020) - Disconnecting the display connectors 02
    iPhone SE (2020) - Disconnecting the display connectors 03
    iPhone SE (2020) - Disconnecting the display connectors 04
    Used tools
    Pry Tool
    • Connector
    1. Using the plastic spudger, lever off the two connectors that are attached to the display (display and home button).
    Used tools
  8. Disconnecting the FaceTime connector

    iPhone SE (2020) - Disconnecting the FaceTime connector 01
    iPhone SE (2020) - Disconnecting the FaceTime connector 02
    iPhone SE (2020) - Disconnecting the FaceTime connector 03
    iPhone SE (2020) - Disconnecting the FaceTime connector 04
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    • 3 × 1.0 mm Phillips
    1. Using the Phillips screwdriver (PH00), loosen the three Phillips screws to remove the cover over the FaceTime connector.
    2. Use a spudger to carefully detach the FaceTime connector from the board.
    3. Now you can remove the display completely.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
  9. Information for battery replacement

    iPhone SE (2020) - Information for battery replacement 01
    • Antenna Flex Cable
    1. The battery in the iPhone SE is secured with adhesive tape. The easiest way to remove them is to pull them out as flat as possible.
    2. If the tapes tear when you pull them out, you may need to lever the battery out. This may damage other components.
    3. To make battery replacement as safe as possible, we recommend that you remove the Taptic Engine in a previous step.
      To remove the Taptic Engine, you must first remove the speaker and the logic board. Then the upper adhesive strips can be pulled out easily as well.
    4. You can also try to disconnect the Taptic Engine without removing the speaker.
    5. To do this, remove the antenna glued to the speaker and bend the small flex cable over the contact of the Taptic Engine to the side.


  10. Removing the iSight camera

    iPhone SE (2020) - Removing the iSight camera  01
    iPhone SE (2020) - Removing the iSight camera  02
    iPhone SE (2020) - Removing the iSight camera  03
    iPhone SE (2020) - Removing the iSight camera  04
    iPhone SE (2020) - Removing the iSight camera  05
    iPhone SE (2020) - Removing the iSight camera  06
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.9 mm Phillips
    • 1 × 3.0 mm Standoff
    • Connector
    1. Unscrew the two screws which fasten the bracket plate of the iSight camera and put the bracket plate aside.

    There are special screwdrivers for removing the internal thread screw, but you can also use a regular, thin slotted screwdriver.

    1. Disconnect the camera by carefully prying off its connector using a spudger.
    2. Then remove the camera from your iPhone using tweezers.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  11. Disconnecting the connector of the volume control cable

    iPhone SE (2020) - Disconnecting the connector of the volume control cable 01
    iPhone SE (2020) - Disconnecting the connector of the volume control cable 02
    iPhone SE (2020) - Disconnecting the connector of the volume control cable 03
    iPhone SE (2020) - Disconnecting the connector of the volume control cable 04
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 1.1 mm Phillips
    • 1 × 2.7 mm Phillips
    1. First remove the screws of the bracket plate located above the connector of the standby and volume button.
    2. Carefully separate the connector from the logicboard with the spudger.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  12. Removing the plastic bracket

    iPhone SE (2020) - Removing the plastic bracket 01
    iPhone SE (2020) - Removing the plastic bracket 02
    iPhone SE (2020) - Removing the plastic bracket 03
    iPhone SE (2020) - Removing the plastic bracket 04
    iPhone SE (2020) - Removing the plastic bracket 05
    iPhone SE (2020) - Removing the plastic bracket 06
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 2 × 1.2 mm Phillips
    • 2 × 1.0 mm Phillips
    • 1 × 2.5 mm Phillips
    • 1 × 1.4 mm Phillips
    1. First unscrew the four Phillips screws from the plastic bracket to be able to remove the bracket afterwards.

    One of the screws is screwed into the side of the backcover.

    1. Remove the other two screws, which attach a kind of connecting item under the plastic bracket, and take it out of your device.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  13. Removing the Wi-Fi antenna

    iPhone SE (2020) - Removing the Wi-Fi antenna  01
    iPhone SE (2020) - Removing the Wi-Fi antenna  02
    iPhone SE (2020) - Removing the Wi-Fi antenna  03
    iPhone SE (2020) - Removing the Wi-Fi antenna  04
    iPhone SE (2020) - Removing the Wi-Fi antenna  05
    iPhone SE (2020) - Removing the Wi-Fi antenna  06
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    Steel Laboratory Spatula
    • 1 × 1.3 mm Phillips
    • 1 × 1.2 mm Phillips
    • Connector
    1. First unscrew the Phillips screws with which the Wi-Fi antenna is attached.
    2. Now carefully lever the antenna connector off the board with a plastic spudger.
    3. Loosen the slightly stuck antenna with the help of a little hot air and a flat, stable lever tool by sliding it under the antenna. We always use a steel spatula in this case.
    4. Once everything is loose, you can remove the antenna from your iPhone SE.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    Steel Laboratory Spatula
  14. Removing the SIM card tray

    iPhone SE (2020) - Removing the SIM card tray  01
    iPhone SE (2020) - Removing the SIM card tray  02
    iPhone SE (2020) - Removing the SIM card tray  03
    Used tools
    SIM Tool
    1. Take a SIM tool or a paperclip to remove the SIM card tray from your phone. To do so, press the SIM tool into the small hole in the SIM card tray.
    Used tools
  15. Disconnecting the logic board connectors

    iPhone SE (2020) - Disconnecting the logic board connectors 01
    iPhone SE (2020) - Disconnecting the logic board connectors 02
    iPhone SE (2020) - Disconnecting the logic board connectors 03
    iPhone SE (2020) - Disconnecting the logic board connectors 04
    iPhone SE (2020) - Disconnecting the logic board connectors 05
    Used tools
    Pry Tool
    • Connector
    1. Carefully detach the three connectors from the logic board with a spudger.
    Used tools
  16. Removing the logic board

    iPhone SE (2020) - Removing the logic board  01
    iPhone SE (2020) - Removing the logic board  02
    iPhone SE (2020) - Removing the logic board  03
    iPhone SE (2020) - Removing the logic board  04
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.4 mm Standoff
    • 1 × 2.1 mm Standoff
    • 1 × 1.6 mm Phillips
    1. Untighten the three screws that hold the logic board in place.
    2. Please note, that the Phillips screw is covered by a sticker (see our photo).

    3. With the screws loosend you can carefully remove the logic board. Next to the two holes for the iSight camera, there is a plastic holder for a screw.
      This plastic holder lies above the logic board.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  17. Removing the speaker

    iPhone SE (2020) - Removing the speaker  01
    iPhone SE (2020) - Removing the speaker  02
    iPhone SE (2020) - Removing the speaker  03
    iPhone SE (2020) - Removing the speaker  04
    iPhone SE (2020) - Removing the speaker  05
    iPhone SE (2020) - Removing the speaker  06
    iPhone SE (2020) - Removing the speaker  07
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    Wiha PicoFinish Y-Type Screwdriver Y000
    • 1 × 1.2 mm Y-type
    • 1 × 2.9 mm Phillips
    • 1 × 2.5 mm Phillips
    • Connector
    • 1 × 1.4 mm Phillips
    • 1 × 2.1 mm Phillips
    1. First unscrew the three screws from the cover plate that is attached above the flexible cable of the speaker, and remove the cover plate.

    For the Y-type screw you need a suitable Y-type screwdriver.

    1. Then carefully separate the speaker connector with a spudger and lift up the flex cable.
    2. Loosen the screws that hold the speaker in place.
    3. As a last step, lift the speaker and the flex cable out of your device.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    Wiha PicoFinish Y-Type Screwdriver Y000
  18. Removing the Taptic Engine

    iPhone SE (2020) - Removing the Taptic Engine  01
    iPhone SE (2020) - Removing the Taptic Engine  02
    iPhone SE (2020) - Removing the Taptic Engine  03
    iPhone SE (2020) - Removing the Taptic Engine  04
    iPhone SE (2020) - Removing the Taptic Engine  05
    iPhone SE (2020) - Removing the Taptic Engine  06
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.0 mm Standoff
    • 1 × 2.0 mm Phillips
    1. First, carefully pull off the small flex cable that is located above the Taptic Engine connector.
    2. Then loosen the screws that hold the Taptic Engine in place.
    3. Use a spudger to carefully detach the Taptic Engine connector and take it out of your phone.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  19. The right tools for your repair

    With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools.
    VIEW NOW
  20. Removing the battery

    iPhone SE (2020) - Removing the battery 01
    iPhone SE (2020) - Removing the battery 02
    iPhone SE (2020) - Removing the battery 03
    iPhone SE (2020) - Removing the battery 04
    Used tools
    Piergiacomi Tweezers 2a SA ESD

    The battery is glued to the case with four adhesive strips. The adhesive strips have tabs to pull them out. The tabs are glued to the top and bottom edges of the battery.

    1. Use tweezers or a spatula to peel off the black tabs. Underneath are the white adhesive strips.
    2. Now pull out the adhesive strips very slowly. Keep the strips as flat as possible at the level of the iPhone.
    3. Firmly hold the battery and iPhone while pulling out the last adhesive strip to prevent the battery from falling out of the device.

      If one of the adhesive strips tears, you have to pry out the battery carefully using a battery spudger. Try to bend the battery as little as possible.

    4. Once all the adhesive strips are off, you can remove the battery.
    Used tools
    Piergiacomi Tweezers 2a SA ESD
  21. Preparing the battery

    In order to position the battery correctly, you can either reinstall all parts except for the logic board, or put the logic board temporarily into the back cover.

    Pay attention to the alignment of the adhesive strips. Check their alignment by placing them into the device for a test.

    1. Remove the large blue protective foil from the adhesive strip and place it in the middle of the underside of the battery.

    When attaching the tape, leave enough space on both sides to fold the tabs over.

    1. Rotate the battery so that the top is up and remove the small blue and pink protective films from the tabs of the adhesive strips.
    2. Stick the tabs to the top of the battery.
    3. Rotate the battery again and pull the pink protective film from the adhesive strips.
  22. Inserting the battery

    iPhone SE (2020) - Inserting the battery 01
    iPhone SE (2020) - Inserting the battery 02
    iPhone SE (2020) - Inserting the battery 03

    Keep distance on all sides between the new battery, the frame and other components.

    1. Insert the battery back into your iPhone SE. Use the battery connector as a guide to align it correctly.

    Once you have inserted the battery, remove the logicboard at this point to properly position the battery.


  23. Installing the Taptic Engine

    iPhone SE (2020) - Installing the Taptic Engine 01
    iPhone SE (2020) - Installing the Taptic Engine 02
    iPhone SE (2020) - Installing the Taptic Engine 03
    iPhone SE (2020) - Installing the Taptic Engine 04
    iPhone SE (2020) - Installing the Taptic Engine 05
    Used tools
    Pry Tool
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.0 mm Standoff
    • 1 × 2.0 mm Phillips
    • Connector
    1. Put the Taptic Engine back between battery and Lightning connector.

    Make sure that the screw holes of the taptic engine fit correctly.

    1. Press the Taptic Engine connector so that it clicks into place.
    2. Fix the Taptic Engine with the screws that were previously loosened.
    3. Put on the small flex cable and attach its connector.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  24. Inserting the speaker

    iPhone SE (2020) - Inserting the speaker  01
    iPhone SE (2020) - Inserting the speaker  02
    iPhone SE (2020) - Inserting the speaker  03
    iPhone SE (2020) - Inserting the speaker  04
    iPhone SE (2020) - Inserting the speaker  05
    iPhone SE (2020) - Inserting the speaker  06
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Wiha PicoFinish Y-Type Screwdriver Y000
    • 1 × 2.1 mm Phillips
    • 1 × 1.4 mm Phillips
    • 1 × 1.2 mm Y-type
    • 1 × 2.9 mm Phillips
    • 1 × 2.5 mm Phillips
    1. Put the speaker back in its original place and press it firmly.

    Be sure to position the flex cable correctly between the battery and speaker.

    1. Now screw the speaker back on.
    2. Attach the connector of the flex cable.
    3. Place the cover plate over the flex cable and fix it with the screws.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Wiha PicoFinish Y-Type Screwdriver Y000
  25. Inserting the logic board

    iPhone SE (2020) - Inserting the logic board  01
    iPhone SE (2020) - Inserting the logic board  02
    iPhone SE (2020) - Inserting the logic board  03
    iPhone SE (2020) - Inserting the logic board  04
    iPhone SE (2020) - Inserting the logic board  05
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.4 mm Standoff
    • 1 × 2.1 mm Standoff
    • 1 × 1.6 mm Phillips
    1. Put the logic board back into its original place. The camera bracket must be seated above the board.
    2. Screw the logic board tight.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  26. Connecting the connectors on the logic board

    iPhone SE (2020) - Connecting the connectors on the logic board 01
    iPhone SE (2020) - Connecting the connectors on the logic board 02
    iPhone SE (2020) - Connecting the connectors on the logic board 03
    • Connector

    Attach the three connectors on the logic board.

    1. First position the connectors over their sockets and then carefully press them down with your finger.
  27. Inserting the SIM card tray

    iPhone SE (2020) - Inserting the SIM card tray  01
    iPhone SE (2020) - Inserting the SIM card tray  02
    1. Slide the SIM card holder back into its corresponding opening on the device frame.

    If the holder does not slide in easily, check the position of the logic board again.

  28. Installing the Wi-Fi antenna

    iPhone SE (2020) - Installing the Wi-Fi antenna  01
    iPhone SE (2020) - Installing the Wi-Fi antenna  02
    iPhone SE (2020) - Installing the Wi-Fi antenna  03
    iPhone SE (2020) - Installing the Wi-Fi antenna  04
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 1.3 mm Phillips
    • 1 × 1.2 mm Phillips
    • Connector
    1. Put the Wi-Fi antenna back into the case of your iPhone SE.
    2. Screw the antenna mount to the case frame.
    3. Then press it lightly to reattach the adhesive film.
    4. Now attach the connector of the antenna.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  29. Installing the plastic bracket

    iPhone SE (2020) - Installing the plastic bracket 01
    iPhone SE (2020) - Installing the plastic bracket 02
    iPhone SE (2020) - Installing the plastic bracket 03
    iPhone SE (2020) - Installing the plastic bracket 04
    iPhone SE (2020) - Installing the plastic bracket 05
    iPhone SE (2020) - Installing the plastic bracket 06
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • 1 × 2.5 mm Phillips
    • 1 × 1.4 mm Phillips
    • 2 × 1.2 mm Phillips
    • 2 × 1.0 mm Phillips
    1. Put the small connector piece in its original place and screw it tight.
    2. Now insert the plastic bracket and screw it tight as well.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  30. Attaching the connector of the volume control cable

    iPhone SE (2020) - Attaching the connector of the volume control cable 01
    iPhone SE (2020) - Attaching the connector of the volume control cable 02
    iPhone SE (2020) - Attaching the connector of the volume control cable 03
    iPhone SE (2020) - Attaching the connector of the volume control cable 04
    iPhone SE (2020) - Attaching the connector of the volume control cable 05
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • Connector
    • 1 × 1.1 mm Phillips
    • 1 × 2.7 mm Phillips
    1. Attach the connector of the standby and volume buttom again.
    2. Put the bracket plate back on the connector and fasten it with the screws.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  31. Installing the iSight camera

    iPhone SE (2020) - Installing the iSight camera  01
    iPhone SE (2020) - Installing the iSight camera  02
    iPhone SE (2020) - Installing the iSight camera  03
    iPhone SE (2020) - Installing the iSight camera  04
    iPhone SE (2020) - Installing the iSight camera  05
    iPhone SE (2020) - Installing the iSight camera  06
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • Connector
    • 1 × 2.9 mm Phillips
    • 1 × 3.0 mm Standoff
    1. Put the camera back into its case opening and press it firmly.
    2. Now attach the camera connector.
    3. Put the cover plate of the camera back on and screw it tight.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  32. Detaching the old and aligning the new adhesive frame

    iPhone SE (2020) - Detaching the old and aligning the new adhesive frame 01
    iPhone SE (2020) - Detaching the old and aligning the new adhesive frame 02
    iPhone SE (2020) - Detaching the old and aligning the new adhesive frame 03
    Used tools
    Piergiacomi Tweezers 2a SA ESD

    After opening and attaching a new adhesive frame, your iPhone is again protected against dust and splash water, but not 100% waterproof!

    1. First remove all remaining adhesive residues on the metal frame and display, so that the new adhesive frame fits smoothly. Use tweezers or a spudger to help you.
    2. Try aligning the adhesive frame on the back cover of your iPhone SE to ensure proper placement.

    The corners of the adhesive frame differ and help with the correct alignment on the back cover.

    Used tools
    Piergiacomi Tweezers 2a SA ESD
  33. Attaching the FaceTime connector

    iPhone SE (2020) - Attaching the FaceTime connector 01
    iPhone SE (2020) - Attaching the FaceTime connector 02
    iPhone SE (2020) - Attaching the FaceTime connector 03
    iPhone SE (2020) - Attaching the FaceTime connector 04
    iPhone SE (2020) - Attaching the FaceTime connector 05
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • Connector
    • 3 × 1.0 mm Phillips
    1. Place the display upright on the upper case frame and connect the FaceTime connector on the logicboard.
    2. Now sideline the display on the the case frame.
    3. Place the bracket plate back over the FaceTime connector and fix it with the three Phillips screws.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  34. Connecting the display

    iPhone SE (2020) - Connecting the display 01
    iPhone SE (2020) - Connecting the display 02
    iPhone SE (2020) - Connecting the display 03
    • Connector
    1. Attach the connectors from the home button and the display to the logic board.
  35. Attaching the battery connector

    iPhone SE (2020) - Attaching the battery connector 01
    iPhone SE (2020) - Attaching the battery connector 02
    iPhone SE (2020) - Attaching the battery connector 03
    iPhone SE (2020) - Attaching the battery connector 04
    iPhone SE (2020) - Attaching the battery connector 05
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
    • Connector
    • 2 × 2.6 mm Phillips
    • 2 × 1.0 mm Phillips
    1. Reattach the battery connector.
    2. Place the bracket plate over the battery connector and fix it with the four Phillips screws.
    Used tools
    Wiha PicoFinish Phillips Screwdriver PH00
    Piergiacomi Tweezers 2a SA ESD
  36. Attaching the display

    iPhone SE (2020) - Attaching the display 01
    iPhone SE (2020) - Attaching the display 02
    iPhone SE (2020) - Attaching the display 03
    iPhone SE (2020) - Attaching the display 04
    • Wrong position
    • Right position
    1. Position the display on the side of the case frame and carefully fold it onto your iPhone.
    2. If a specific cable is not seated correctly, problems like spots on the display can occur. Therefore, before closing, make sure that the chip on the cable is in the right position. Use our photo to find the exact position.

    3. Then press the entire surface of the display into the case frame.
  37. Fastening the rear case screws

    iPhone SE (2020) - Fastening the rear case screws  01
    iPhone SE (2020) - Fastening the rear case screws  02
    Used tools
    Wiha PicoFinish Pentalobe Screwdriver PL1
    • 2 × 3.4 Pentalobe
    1. Screw the two pentalobe screws to the left and right of the Lightning connector into the rear case of your iPhone SE.
    Used tools
    Wiha PicoFinish Pentalobe Screwdriver PL1
Ø 5 (4 Ratings)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Submit rating

Submit rating

How did you like this repair guide?

Exceptional

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 79.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN