Honor 10 - Replacing the screen

1. Turn off your device by holding down the power button until the “Power off” option appears.
2. Use your finger to confirm that you want to shut down your Honor 10 and wait until the screen goes blank.

Here in the picture you see another device, because the display of the Honor 10 did not function any more.

1. The back cover’s firmly glued to the chassis. Heat the device evenly with hot air to soften the glue. A temperature of 60 - 80°C should be sufficient. As a rule of thumb, you should still be able to touch your device without it being uncomfortably hot.
2. The easiest way to loosen the back cover is to use a flat and flexible tool such as the iPlastix or iFlex. You will also need several picks to unstick the back cover all around.

1. Heat the spot where you start and place a flat tool between the back cover and the frame.

The iPlastix is made of plastic, so it won't scratch the device. On the other hand, it's very soft and tricky to insert.

Be extra careful, the back cover can break very easily. If necessary, apply the heat several times and try again. Removing the back cover might take a little longer. Take a little more time and work carefully to make sure you don't break anything.

1. Once the tool is inserted, stick a pick into the gap to keep it open. Then run the tool around the entire edge to gradually loosen the glue.
2. Then heat the next part and insert the picks one by one.

Use a suction cup to lift the glass if you can’t find anywhere to insert the tool

All components in the device are covered by a black graphite foil, which serves for better heat distribution.

1. Loosen the foil on the upper side and fold it down.
2. You can heat the adhesive again to loosen it more easily.

• 3 × 2,8 mm Phillips
• Battery connector

Before starting the repair, always disconnect the battery contact first to prevent short circuits and avoid accidentally turning on your device during the repair.

1. Use a phillips screwdriver (PH00) to remove the phillips screws. Then take off the cover. The cover is hooked under on the upper side. Put all the parts in the same section of your magnetic pad.
2. Using the spudger, carefully disconnect the battery contact from the motherboard. Use a plastic tool to avoid short circuits.

Always lever from a side where there are no small components on the mainboard. This way you avoid damage.

• 4 × 3,4 mm Phillips
• 2 × 2,8 mm Phillips
• Camera connector

Next, remove the two camera modules. The camera contacts are secured with a cover.

1. Loosen all Phillips screws first. One of them is covered with a small white sticker.

The screws in Honor 10 have different lengths. Be careful not to mix them up.

1. Then carefully lever the cover loose with a pair of tweezers. The cover is hooked in several places.
2. Next loosen the connectors carefully with a spudger.
3. Finally remove both cameras from the device.

Make sure that no dirt or fingerprints get on the camera lenses.

• Antenna connector
• USB flex cable connector
• Display connector

Several flexible flat cables and an antenna are still connected to the mainboard.

1. Loosen the contacts of the flexbile flat cables with the spudger. The cables connect the display and the USB board to the motherboard.
2. Loosen the antenna cable carefully by turning the tweezers. Do not lever off the contact with a spudger. There is a danger of damaging the socket on the circuit board.
3. Remove the SIM card holder if it is still in the device.
4. Carefully lever the board up a little and then take it out.

• 4 × 2,8 mm Phillips
• 3 × 3,4 mm Phillips

The speaker is fixed with several screws, lightly glued and hooked to the frame.

1. First fold over the heat shield.
2. Loosen the Phillips screws of different lengths. Sort them on a magnetic mat, for example, so you don't mix them up when you insert them again.
3. Then lever the speaker in several places until you can lift it a little and remove it.

• Antenna connector
• USB flex cable connector
• Fingerprint connector

1. First remove the flex cable running over the battery.
2. Loosen the connector and remove the cable.
3. Use tweezers again to release the black antenna cable and lever it out of the metal clamps.
4. Loosen the small contact for the fingerprint sensor.
5. Carefully lever the USB board up with a spudger. Push it away from the frame at the bottom to release it.
6. Then remove the board from the device. Make sure that the rubber seals for the USB socket and headphone socket remain on the board. If they remain in the case, take them out and attach them to the board.

The battery is glued into the case generously.

1. You can loosen the glue more easily by warming it up again. But never heat the battery directly, heat it from the display.
2. Slide a flat tool like the iPlastix under the battery.
3. If you can't get it under the battery, you can also use a wider, more stable tool like the Battery Spudger.
4. Then move a flat tool around and gradually lift the battery out of the device.

Try to bend the battery as little as possible and take care not to damage the surface.

1. The earpiece is lightly glued into the device.
2. Heat the adhesive and lift out the earpiece.
3. Note the orientation of the golden contacts to insert the earpiece correctly later.
4. Pull the black antenna out of its sideways guide.

1. Check if your replacement display already has standby and volume keys built in. If not, you have to copy them from the old display.
2. Heat the flex cable with the four golden contact surfaces and loosen it carefully with a steel spatula or another very thin tool.
3. Drive the steel spatula between the cable and the housing frame and loosen the adhesive there as well.
4. Remove the component from the frame with the buttons.
5. Lever out the silver clip that fixes the buttons in the frame.
6. Remove the two buttons.
7. Install all parts in the new display. Make sure that the silver clip fixes the keys and the buttons work.

1. Now compare your display with the new replacement display and check if you still need to take over small parts such as seals.
2. Also check the spare part for external damage. If the glass is scratched or the flex cable is damaged, do not install the display but exchange it with your dealer.
3. If everything is in good condition, remove all plastic film over the various adhesive surfaces.

1. Place the black antenna in its sideways guide.
2. Put the earpiece in its place.

Make sure that the golden contacts point to the left in the device.

1. Place the battery in the device.
2. Make sure it has some space on all sides and is not pressed against one side.

• Antenna connector
• USB flex cable connector
• Fingerprint connector

1. Make sure that the rubber seals for the USB socket and the headphone socket are on the board.
2. Place the board on the bottom edge and press it down until it fits properly.
3. Connect the black antenna cable and press it into the silver brackets.
4. Connect the fingerprint sensor and the wide flex cable. The white arrow must point upwards.

• 4 × 2,8 mm Phillips
• 3 × 3,4 mm Phillips

1. Insert the speaker together with the heat shield and press it firmly into the device until it sits properly.
2. Secure the speaker with the Phillips screws.

• Antenna connector
• USB flex cable connector
• Display connector

1. Insert the mainboard into the device and make sure that you do not pinch any cables under the board.
2. Press the motherboard a little and check if it fits correctly.
3. Insert the SIM card holder. If it gets stuck, don't push it in with force, but check if the mainboard is seated correctly.
4. Connect the two flex cables and the antenna cable. You can use a pair of tweezers to position the antenna and then connect it with a spudger.

• 2 × 2,8 mm Phillips
• 4 × 3,4 mm Phillips

1. Place both camera modules in their openings.
2. Connect the connectors. Make sure they click into place with a slight click.
3. Position the cover on the bottom edge. It must be hooked underneath there.
4. Then press the cover everywhere until it fits properly.
5. Screw the cover together with the screws of different lengths.

• Battery connector
• 3 × 2,8 mm Phillips

1. Connect the battery to the motherboard.
2. Put on the cover and screw it on.
3. The cover is hooked into the upper side.
4. Finally, fold over the black foil and stick it on.

1. There are several ways to put the backcover back on again.
2. If the existing adhesive is still in place and available in all places, you can use it again.
3. If this is not the case you have to use new glue.
4. First remove all old glue residues.
5. Then apply the new glue. You can use thin double-sided tape or liquid glue. Be very sparing with the glue and make sure it doesn't get into the device.

1. Finally, place the back cover flush on the frame and make sure it is exactly centered.
2. Press it firmly so that the adhesive bonds properly.
3. You can also warm it up a bit and keep it between a few books for 30 minutes so that the glue will bond properly.