HUAWEI P30 Pro back cover repair guide

The back of the enclosure is broken or scratched.

In just three easy steps you can replace the scratched or splintered back cover of the HUAWEI P30 Pro yourself. Expensive repair shops or service centres are not necessary - this simple repair you can do on your own to save money and time. In our store you can get original spare parts that will fit perfectly.

For each step you will find a detailed description of how to proceed and which tools you need. In addition, you will find short video sequences that visualize the procedure even better.

Before you start, you should clean your work surface and provide enough light. We would be happy if you leave us feedback or an evaluation after your repair.

Required tools

Flat Picks

Flat Picks

You need a very flat tool such as a flat pick to pry out parts that are glued in place.
from €11.95 on Amazon
Heat gun

Heat gun

You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.
from €15.99 on Amazon
iFlex Opening Tool

iFlex Opening Tool

Opening your smartphone can be a very delicate operation, especially if the glue is very persistent. The blade of the flexible but sturdy iFlex measures just 0.15 mm, so it fits in even the smallest gaps, such as between the screen and the frame. The practical iFlex is made of stainless steel and sits comfortably in the hand. This makes it the perfect assistant for every smartphone repair.
from €10.95 on Amazon
iPlastix Opening Tool

iPlastix Opening Tool

Do you want to open your smartphone or lever out large parts like the battery? Then the iPlastix with its large blade will help you. The practical assistant is made of flexible, especially sturdy plastic and lies comfortably in the hand. Thanks to its design, you can even get into smaller gaps, for example to lift the screen or to prevent it from sticking together again.
on Amazon
Tweezers

Tweezers

We recommend using tweezers to remove screws and various small parts from your device.
on Amazon
Plastic prying tool

Plastic prying tool

You need a flat plastic prying tool to disconnect the various plugs and connectors.
from €14.99 on Amazon
Steel Laboratory Spatula

Steel Laboratory Spatula

You need a flat and sturdy prying tool to disconnect glued parts.
on Amazon
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
from €10.84 on Amazon

Required replacement part

HUAWEI P30 Pro Backcover

HUAWEI P30 Pro Backcover

from €12.99 on Amazon

Show all replacement parts for the Huawei P30 Pro

Getting started with the repair of your Huawei P30 Pro

If you get stuck or have questions, you can post a comment. We’d be happy to help.

3 steps

Switch off your Huawei P30 Pro
To avoid short circuits during the repair you should always switch off the device first.
If the screen cannot be used anymore because of a defective display, this is not that problematic.The device will turn off immediately, when you disconnect the battery in a few steps.

Removing the back cover
The Huawei P30 Pro is opened via the heavily glued back cover.
Heat the entire edge of the backcover and especially the part where you start to loosen the backcover. Do not heat the phone too much, but only so far that you can still touch it well.
Place the suction cup on the bottom of the device and pull to create a small gap between the back cover and the frame.
Then try to get into the gap with your tool. With the iFlex this is a bit easier than with the iPlastix, because it is made of metal and a bit more stable. We recommend to continue with a plastic tool as soon as possible.
Be especially careful with this step, as the back cover is made of glass and can break easily.
Do not push the tool too far into the device and be careful not to scratch the backcover with the edges of the tool.

Be especially careful near the cameras to avoid damaging them.
Then heat the area you are working on again and move the tool further along the edge.
To prevent the glue from sticking together again, you can use several picks and insert them into the already loosened part. Then go around the whole frame and loosen the glue bit by bit.
Attention: after a repair the phone is basically no longer waterproof.
Installing the back cover
Before you put the back cover on the frame, check the glue. It should be evenly distributed around the edge so that the backcover is flush with the frame. Remove excess glue if necessary.
If you like, you can also remove the old glue and use a new adhesive frame.
Position the backcover centered over the device and place it slowly. Do not press it firmly until it is correctly positioned.
Heat the back cover again with hot air to make the adhesive bond even better.
As long as the glue cools down, you can press the back glass firmly with your fingers or weigh it down slightly.
Please note, that the smartphone is no longer 100% protected against liquid damage after repair.