HUAWEI P8 lite front camera repair guide

The front-facing camera isn’t working or your pictures are blurry.

In this repair guide, we show you how to replace your Huawei P8 lite’s defective front camera on your own. You need this repair if the front camera isn’t working, the aperture doesn’t open, or your pictures are blurry.

Required tools

Menda ESD Spudger

Menda ESD Spudger

You need a flat plastic prying tool to disconnect the various plugs and connectors.
from €26.38 on Amazon
Pick Set

Pick Set

You need a flat but stable tool such as a pick to pry out parts that are glued in place.
from €14.99 on Amazon
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
from €10.84 on Amazon
Wiha PicoFinish Torx Screwdriver T5

Wiha PicoFinish Torx Screwdriver T5

from €10.23 on Amazon

Required replacement part

Huawei P8 lite Frontcamera

Huawei P8 lite Frontcamera

from €129.00 on Amazon

Show all replacement parts for the P8 lite

Steps

17 Steps

Switching off your device

Step 1

Removing the SIM and microSD cards

Step 2

Removing the back cover

Step 3

Removing the speaker

Step 4

Disconnecting the battery and display contacts

Step 5

Removing the upper cover

Step 6

Disconnecting the connections to the PCB

Step 7

Removing the motherboard

Step 8

Removing the front camera

Step 9

Installing the front camera

Step 10

Installing the motherboard

Step 11

Making the connections to the PCB

Step 12

Installing the upper cover

Step 13

Connecting the battery and display contacts

Step 14

Installing the speaker

Step 15

Attaching the back cover

Step 16

Inserting the SIM and microSD cards

Step 17

Getting started with the repair of your P8 lite

If you get stuck or have questions, you can post a comment. We’d be happy to help.

17 steps

Switching off your device
Before your start the repair, switch off your device by holding down the standby button until the shutdown dialog appears on the screen.

Use the touchscreen to confirm shutdown.
Removing the SIM and microSD cards
Remove the two trays for the SIM and microSD cards from the enclosure by pressing a SIM Tool or paperclip into the little hole until the tray comes out. Then remove both trays and the cards.
Removing the back cover
Carefully disconnect the back cover from the enclosure frame. The back cover is hooked onto the frame at several points. Undo the hooks by inserting a pick between the back cover and the frame. Repeat this process for the entire device.

Take the back cover off of your device.
Removing the speaker
Remove the seven screws that hold the speaker in place.
3 x 2.7 mm PH00 Phillips screw
4 x 3.7 mm T5 Torx screw

Remove the speaker from your device.
Disconnecting the battery and display contacts
Remove the three screws.
3 x 2.7 mm PH00 Phillips screw

Remove the silver cover from your device.

Carefully disconnect the battery contact from the PCB by inserting your tool below the contact and lifting it. Make sure you don’t damage or break off any of the parts on the board.

Disconnect the display contact the same way.
Removing the upper cover
Remove the seven screws that attach the cover to the device.
5 x 2.7 mm PH00 Phillips screw
2 x 3.7 mm T5 Torx screw

The cover is made of two parts. Carefully remove the larger upper cover using a pair of tweezers.

The NFC antenna’s contact is glued to the bottom of the smaller cover. Turn the cover over so you can disconnect the contact.

Carefully disconnect the contact by gently pushing the steel laboratory spatula between the contact and the cover.

Also remove the little cover.
Disconnecting the connections to the PCB
Disconnect the touchscreen contact from the motherboard. Stick your tool under the contact and lift it up.

Now disconnect the cable for the sensors the same way.

The contact for the control buttons is secured by a little bracket. Lift the bracket to release the contact and then carefully pull out the cable. To avoid damaging the cable, don’t pull too hard or bend it too much.

Remove the control buttons from the device.
Removing the motherboard
Lift the PCB out of your device. Insert something like a spudger below the board and lift it up.

Grip the PCB between your thumb and finger, and remove it.

Removing the front camera
Disconnect the front camera’s contact from the bottom of the board.

Remove the front camera.
Installing the front camera
Put the new front camera in the appropriate position and connect it to the socket on the bottom of the motherboard. You’ll hear the contacts click into place.
Installing the motherboard
Put the PCB in the enclosure. Make sure it’s in the exact right position. Insert the PCB at the upper end of the device first so you can push the headphone jack through the opening in the frame.
Making the connections to the PCB
Put the control buttons back in and connect them to the motherboard.

Slide the cable back into the socket and lock the socket with the bracket.

Carefully press the connector into the socket to connect the sensors to the board.

Do the same thing with the touchscreen connector.
Installing the upper cover
Put the smaller cover upside down on the battery so you can connect the NFC antenna’s contact again.

Put the antenna contact back in the hollow on the cover. Firmly press the contact and the cover together so they’ll stick to each other.

Put the cover back in the right position on the motherboard.

Now put the larger cover back on. Make sure the little cover and the big cover hook onto each other.

Use the seven screws to attach the covers to the enclosure.
5 x 2.7 mm PH00 Phillips screw
2 x 3.7 mm T5 Torx screw
Connecting the battery and display contacts
Connect the PCB to the display by carefully pressing the display contact into the socket on the PCB. You’ll be able to hear the connector click into place.

Connect the battery contact the same way.

Position the silver cover on the PCB.

Use the three screws to attach the cover to the board.
3 x 2.7 mm PH00 Phillips screw
Installing the speaker
Put the speaker back in the lower end of the device.

Use the seven screws to attach the speaker to the device.
3 x 2.7 mm PH00 Phillips screw
4 x 3.7 mm T5 Torx screw
Attaching the back cover
Put the back cover back on.

Use your finger to press it onto the entire frame so all the clips on the back cover click into place on the enclosure.
Inserting the SIM and microSD cards
Put the SIM and microSD cards back in the corresponding trays and insert the trays into your device.

Push them in until they’re flush with the enclosure.