Samsung Galaxy S9+ screen repair guide

The screen is broken or remains black.

With this detailed step-by-step guide, you can easily replace your Galaxy S9+ display at home.

A replacement is necessary when the glass is shattered, the touchscreen does not respond to touch anymore, or the display remains black or flickers. During this repair, we replace the entire display unit including the frame, not just the broken screen. You may have to take some small parts from the old display unit, depending on how the new spare part is equipped.

The repair is a bit difficult as the Galaxy S9+ has to be opened via the glass backcover. Unfortunately, this is a rather cumbersome procedure, so plan enough time for it.

Do a backup before the repair, use a clean work surface and reserve enough time. If you are stuck at any point, just contact our live chat or write a comment on the corresponding step.

Required tools

Flat Picks

Flat Picks

You need a very flat tool such as a flat pick to pry out parts that are glued in place.
from €11.95 on Amazon
Heat gun

Heat gun

You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.
from €15.99 on Amazon
iFlex Opening Tool

iFlex Opening Tool

Opening your smartphone can be a very delicate operation, especially if the glue is very persistent. The blade of the flexible but sturdy iFlex measures just 0.15 mm, so it fits in even the smallest gaps, such as between the screen and the frame. The practical iFlex is made of stainless steel and sits comfortably in the hand. This makes it the perfect assistant for every smartphone repair.
from €10.95 on Amazon
For storing screws

For storing screws

We recommend storing your screws so you don’t mix up the various screws and small parts.
from €10.99 on Amazon
Tweezers

Tweezers

We recommend using tweezers to remove screws and various small parts from your device.
on Amazon
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
from €10.84 on Amazon

Required replacement part

Samsung Galaxy S9+ Screen

Samsung Galaxy S9+ Screen

from €10.99 on Amazon

Show all replacement parts for the Galaxy S9+

Steps

32 Steps

Switching off your device

Step 1

Removing the back cover

Step 2

Disconnecting the fingerprint sensor

Step 3

Removing the NFC antenna

Step 4

Disconnecting the battery contact

Step 5

Removing the battery

Step 6

Removing the speaker

Step 7

Removing the front camera & sensor

Step 8

Removing the SIM and microSD card tray

Step 9

Removing the motherboard

Step 10

Removing the vibration motor

Step 11

Removing the sensors

Step 12

Removing the earpiece

Step 13

Removing the headphone jack

Step 14

Removing the USB-Board

Step 15

Preparing the new display

Step 16

Installing the USB board

Step 17

Installing the headphone output

Step 18

Installing the earpiece

Step 19

Installing the sensors

Step 20

Installing the vibration motor

Step 21

Installing the motherboard

Step 22

Inserting the SIM and microSD card tray

Step 23

Installing the front camera & sensor

Step 24

Inserting the battery

Step 25

Installing the speaker

Step 26

Connecting the battery

Step 27

Installing the NFC antenna

Step 28

Connect fingerprint sensor

Step 29

Preparing the backcover

Step 30

Attaching the back cover

Step 31

Testing the display

Step 32

Getting started with the repair of your Galaxy S9+

If you get stuck or have questions, you can post a comment. We’d be happy to help.

32 steps

Switching off your device
Turn off your device by holding down the power button until the “Power off” option appears.
Use your finger to confirm that you want to shut down your Galaxy S9+ and wait until the screen goes blank.
Removing the back cover
The back cover’s really glued to the chassis. Heat the device evenly with hot air to soften the glue. A temperature of 60 - 80°C should be sufficient. As a rule of thumb, you should still be able to touch your device without it being uncomfortably hot.
The easiest way to loosen the back cover is to use a flat and flexible tool such as the iPlastix or iFlex. You will also need several picks to unstick the back cover all around.
Heat the spot where you start and place a flat tool between the back cover and the frame.
The iPlastix is made of plastic, so it won't scratch the device. On the other hand, it's very soft and tricky to insert.
Be extra careful, the back cover can break very easily. If necessary, apply the heat several times and try again. Removing the back cover might take half an hour. Take a little more time and work carefully to make sure you don't break anything.
Once the tool is inserted, stick a pick into the gap to keep it open. Then run the tool around the entire edge to gradually loosen the glue.
Then heat the next part and insert the picks one by one.
The back cover glue is extra strong on the lower edge.
Once the back cover is loosened, lift it very slightly. The fingerprint sensor underneath the camera is still connected with a cable.
Use a suction cup to lift the glass if you can’t find anywhere to insert the tool
Disconnecting the fingerprint sensor
After detaching the back cover, carefully lift it and disconnect the fingerprint sensor using the spudger.
Then you can completely remove the back cover and set it aside.
Removing the NFC antenna
11 × 3,87 mm Phillips

Remove the screws that attach the upper cover to the display.
The cover is latched onto the case, the lower part of the antenna is lightly glued in place. Slide a flat tool under the latches to disconnect them.
Now remove the antenna.
Disconnecting the battery contact
Battery connector

Using the spudger, carefully disconnect the battery contact from the motherboard.
Removing the battery
The battery glue is very strong, so you should use hot air again.
Never heat the battery directly and don't bend it.
The battery is glued around the outer edges but not at the center.
Apply the hot air from the display side.
We recommend running a flat tool, such as the iFlex, all around the battery.
Now take out the battery.
Be careful not to damage the battery. Take your time and heat the glue several times.
Removing the speaker
5 × 3,87 mm Phillips

Remove the screws that attach the speaker to the display and then remove it.
Removing the front camera & sensor
Camera connector

Sensor connector

Disconnect the connectors of the front camera and the sensor.
Then you can pry out the front camera and the sensor out of the chassis and then remove them.
Removing the SIM and microSD card tray
Use the SIM tool to eject the SIM card tray from your device and then remove the tray with your fingers.
Removing the motherboard
Connectors

Using the spudger, carefully disconnect the marked contacts from the logic board.
Now you can carefully remove the motherboard. Make sure it doesn’t get caught on the connectors you already disconnected.
The USB port is still connected to the back of the board. Once you’ve lifted the board, you can use the spudger to disconnect this contact.
Then set the board aside in a safe place.
There's a small plastic pin in the opening of the SIM tray. Make sure it doesn't fall out.
Removing the vibration motor
The vibration motor is glued to the enclosure. Carefully detach the motor by inserting your tool between the enclosure and the motor.
Remove the motor.
Removing the sensors
The sensor cable is also glued to the display. Carefully detach it with a flat tool. Make sure you don’t damage it.
Then you can use a pair of tweezers to remove the cable.
Removing the earpiece
The earpiece is glued to the enclosure. Carefully detach it with a flat tool like the steel spatula.
Removing the headphone jack
1 × 3,3 mm Phillips

Unscrew the screw holding the jack in place.
Disconnect the headphone jack’s contact from the PCB. Using the spudger, carefully pry the contact out of the socket.
Remove the headphone jack from the enclosure.
Removing the USB-Board
4 × 3,3 mm Phillips

Remove the marked screws.
Remove the two antenna cables from their guide.
Then you can use the spudger to carefully pry out the board and remove it entirely.
Preparing the new display
Protective film

In the new display’s enclosure, all the adhesive surfaces and thermal pads are covered with transparent protective film. Remove the protective film before you start with assembly.

Installing the USB board
4 × 3,3 mm Phillips

Reinstall the USB board.
Make sure the entire flexible cable is flush with the enclosure.
Carefully press the antenna cables back into the appropriate guide using a blunt object such as a pair of tweezers with rounded tips.
Then fasten the screws again.
Installing the headphone output
1 × 3,3 mm Phillips

Put the jack in its position at the lower edge of the enclosure.
Connect the plug contact.
Then fasten it with the appropriate screw.
Installing the earpiece
Put the earpiece back in the enclosure.
Press it on a little so the glue will stick better.
Installing the sensors
Insert the sensor cable in the corresponding recess in the upper edge of the enclosure.
Press the sensor firmly with your finger so the glue will stick again.
Installing the vibration motor
Put the vibration motor in the little round opening on the left side of the enclosure.
Use your fingers to press the motor firmly into place.
Installing the motherboard
1 × 3,3 mm Phillips

Connectors

Now you can put the motherboard back in.
First connect the USB port on the back of the board.
Then you can put the board back in the enclosure. Make sure no cables or connectors get stuck under the board.
Fasten the motherboard with the marked screw.
Now connect the marked contacts to the board again.
Inserting the SIM and microSD card tray
Insert the SIM card tray back into your device. Make sure the tray is positioned properly.
Installing the front camera & sensor
Put the front camera and the sensor in the opening at the upper edge of the enclosure and reconnect the connectors.
Inserting the battery
Put the battery in the enclosure. It fits perfectly into the compartment in the middle of the enclosure.
Press the battery firmly into the enclosure so the glue will stick better.
Remove excess adhesive so that the battery sits flat in the phone.
Installing the speaker
5 × 3,87 mm Phillips

Now put the speaker at the lower end of the enclosure.
Press it gently with your fingers until it clicks into place in the enclosure.
Then reinsert the marked screws.
Connecting the battery
Battery connector

Connect the battery to the motherboard. Press the contact onto the connection on the motherboard until you hear it click into place.
Installing the NFC antenna
11 × 3,87 mm Phillips

Put the cover with the antenna back in the enclosure after hooking it onto the top of the enclosure.
Then press the cover with your fingers until it clicks gently into place all over.
Fasten the phillips screws.
Connect fingerprint sensor
Before attaching the back cover, plug in the fingerprint sensor connector.
Use a plastic tool to reach the connector.
Preparing the backcover
Before you put the back cover back on the case, inspect the adhesive. It should sit evenly on the edge so that the back cover can be placed flush. Remove excess glue if necessary.
Attaching the back cover
Put the back cover back in its original position.
Press the back cover on all over so the glue will stick.
You can also heat your device with hot air and then clamp it or weight it down with a couple books so the glue will stick better.
Testing the display
Turn on your device and test it with the integrated test mode.
Access the test mode by dialing *#0*#
Follow the instructions on your screen.