iPhone X - Replacing the iSight camera

1. Turn off your iPhone X before making repairs to protect it from potential damage. To do so, press the standby button and one of the two volume buttons simultaneously for about three seconds.
2. When the "Power Off" slider appears on the display, wipe it from left to right. Your iPhone will shut down completely within about 10 seconds.

• 2 × 6,8 mm Pentalobe

You need a pentalobe screwdriver (PL1) to open your iPhone X.

1. Remove the two pentalobe screws located to the right and left of the Lightning connector and put them in a screw storage box.

To ensure that you do not lose any of the removed components and screws, we recommend that you use a screw storage box. For this purpose, you can for example convert an old sewing box. We use a high-quality magnetic pad for our repairs, on which the removed components can also be arranged in the same way as they were installed in the telephone. This way you know exactly where each screw was located, which makes it much easier for you to assemble later.

iPhone X is opened via the display. Since it is strongly glued to the rest of the case, you have to heat the glue first to be able to remove the display.

1. Place your iPhone X on a soft and clean surface to avoid scratching the back of your iPhone X when lifting the display.
2. Now use a hot air tool, such as a hot air dryer or a regular hairdryer, to run evenly over the glued edge of the display.

The rule of thumb is to heat your device only enough to be comfortable to touch without being uncomfortably hot.

Once the iPhone X has been opened, no warranty can be given for waterproofness. Also the warranty for protection against dust and splashing water of the IP67 classification expires.

1. Place the suction cup on the bottom edge of your device and pull it upwards to create a narrow gap between the stainless steel and display frame.
2. Insert a sturdy, flat tool into the narrow gap to enlarge it. At the same time, press the display slightly upwards with the tool, using flat plastic picks.

Be careful not to go further than 5 mm into the gap with your tool to avoid damaging any components inside the Iphone X.

1. Move the tool one step at a time around the frame of your iPhone to remove the stuck display completely. Use the plectrum to keep pushing upwards so that the noses come off the stainless steel frame.

To avoid overstretching the sensitive flex cables connected to the display, you should not completely fold the display over while it is still connected.

1. Remove the display from the aluminium frame by gently pushing it upwards with a hard plastic plectrum.
2. When the display is completely detached, you can slowly fold it up to the side of the standby button.
3. Lean it against a stable object so that it remains in a vertical position.

• 1 × 3,0 mm Y-Type
• 3 × 1,0 mm Y-Type
• 1 × 3,6 mm Y-Type
• Connector

When starting the repair, always disconnect the battery connector to avoid a potential short circuit.

Note that the screws installed in iPhone X vary in length.

1. Unscrew the Y-type screws with a Y-type screwdriver and remove the cover plate.
2. Now carefully disconnect the battery connector by sliding it under with a flat plastic tool. We use a plastic spudger for this.

• Display Connector
• Earpiece Connector

The display is attached to the rest of the iPhone X via three connectors.

To avoid damaging something on the logicboard while disconnecting the connectors, you should always use your tools from the side where there are no components.

1. Use a spudger to carefully remove the connectors from the Logicboard one by one. Please be aware, that the ear piece flex cable on the top of the display is slightly glued.
2. When all connectors are disconnected, you can remove the display completely.

• 1 × 2,2 mm Phillips
• 1 × 1,9 mm Phillips
• Camera Connector

1. Loosen the two Phillips screws that secure the bracket plate of the iSight camera.
2. Lift up the small metal eyelet under which the bracket plate is clamped, then remove the plate.
3. Carefully separate the two connectors of the iSight camera with a spudger.
4. Carefully lever the camera out of its back cover lead with a spudger as well and put it aside.

• 1 × 2.2 mm Phillips
• Connector
• 1 × 1.9 mm Phillips

1. Place the iSight camera back in its original position and press it down.
2. Attach in the two connectors of the cameras.
3. Postition the cover plate, so that the metal tab goes over the cover plate.
4. Screw in the cover plate using the Phillips screws.

After applying a new adhesive strip, the iPhone is again protected against dust and splash water, but it is not 100% waterproof.

1. To ensure that the new adhesive frame fits properly everywhere, you must first remove all remaining adhesive residue on stainless steel and display frames.
2. Align the adhesive frame correctly and then pull off the protective film from the underside of the adhesive frame.

The corners of the adhesive frame are different and will help you align it correctly with your device's frame.

1. Place the adhesive frame only on one edge of the frame at first and press it down firmly as you go.

You can use the plastic spudger to press it down so that the frame is as smooth as possible.

1. Then pull off the middle part of the protective film.
2. Finally, remove the remaining protective film from the edge of the housing so that only a transparent adhesive film remains.

You can leave the remaining protective film on the edge of the housing until you have connected the display and attached the cover plates. This prevents anything from sticking to the adhesive frame beforehand.

• Display Connector
• Earpiece Connector

1. To prevent the sensitive flex cables from being overstretched when connecting the display, place the display on the side of the frame of your iPhone X and lean it against a stable object.
2. Connect the three display connectors by gently pressing them until you feel them click into place.

You may need to press the lower connector with the spudger to make sure it is properly seated.

• Connector
• 1 × 3,0 mm Y-Type
• 3 × 1,0 mm Y-Type
• 1 × 3,6 mm Y-Type

1. Reattach the battery connector.
2. Then put on the bracket plate and fix it with the Y-Type screws.

1. Take the display in both hands and carefully fold it over.
2. Press it down along the frame one by one.

Test the display and other functions of your iPhone before gluing it in place.

• 2 × 6.8 mm Pentalobe

1. Screw the two pentalobe screws to the left and right of the Lightning connector tight.