LG G6 front camera repair guide

Your selfie camera isn't working.

In this repair guide, we show you how to replace the defective front-facing camera of your LG G6. You need this repair if the front camera isn’t working, your pictures are blurry, or the camera doesn’t focus.

Required tools

Flat Picks

Flat Picks

You need a very flat tool such as a flat pick to pry out parts that are glued in place.
from €11.95 on Amazon
iFlex Opening Tool

iFlex Opening Tool

Opening your smartphone can be a very delicate operation, especially if the glue is very persistent. The blade of the flexible but sturdy iFlex measures just 0.15 mm, so it fits in even the smallest gaps, such as between the screen and the frame. The practical iFlex is made of stainless steel and sits comfortably in the hand. This makes it the perfect assistant for every smartphone repair.
from €10.95 on Amazon
Tweezers

Tweezers

We recommend using tweezers to remove screws and various small parts from your device.
on Amazon
Plastic prying tool

Plastic prying tool

You need a flat plastic prying tool to disconnect the various plugs and connectors.
from €14.99 on Amazon
Steel Laboratory Spatula

Steel Laboratory Spatula

You need a flat and sturdy prying tool to disconnect glued parts.
on Amazon
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
from €10.84 on Amazon

Show all replacement parts for the G6

Steps

16 Steps

Remove front camera

Step 1

Insert front camera

Step 2

Switch off the device

Step 3

Remove back cover

Step 4

Remove speaker

Step 5

Remove midframe

Step 6

Disconnect the battery

Step 7

Remove SIM tray

Step 8

Remove logic board

Step 9

Insert logic board

Step 10

Insert SIM tray

Step 11

Connect battery

Step 12

Insert midframe

Step 13

Insert speaker

Step 14

Attach rear glass

Step 15

Test the display

Step 16

Getting started with the repair of your G6

If you get stuck or have questions, you can post a comment. We’d be happy to help.

16 steps

Remove front camera
Front camera connector

Unplug the front camera connector and take out the camera.
Insert front camera
Place the front camera in its opening in the logic board.
Plug on the connector.
Switch off the device
Turn off your device by holding down the power button on the back until the “Power off” option appears.
Tap to confirm and wait until the screen goes black.
Remove back cover
To loosen the back cover, use a heat gun or an ordinary hair dryer. Warm glue is easier to loosen, allowing you to remove the back cover.
The easiest way to loosen the back cover is to use a flat and flexible tool such as the iFlex.
We also recommend inserting flat picks to prevent the glue from sticking again.

Heat the entire rear glass. It's glued all around the edges and around the home button and over the USB port.

Insert the iFlex between the rear glass and the frame, but not more than 5 mm.

Be extra careful, the back cover can break very easily. Don't pry with the tool, but only slide it around the edges. If necessary, apply the heat several times and try again. Removing the back cover might take a while. Take a little more time and work carefully to make sure you don't break anything.

Once the rear glass comes off in one place, insert a pick into the gap to keep it open.

Then run the iFlexit around all the edges to gradually loosen the glue.

The rear glass has extra glue around the home button and over the USB port. Here you need to insert the iFlexit a little deeper. But not to far, or you could damage parts on the home button.
Once the rear glass is unglued, you can lift it off. There's not cable attached.
Remove speaker
4 × 2.7 mm Phillips

The LG G6 has only one screw length and only the midframe and speaker are screwed in.
Remove the equal-length Phillips screws from the speaker and store them for later.
Then pry out the speaker from the side of the battery and take it out of the device.
Remove midframe
7 × Phillips

Remove the equal-length Phillips screws from the midframe and store them for later.
Slide a flat, thin tool into the opening and pry out the midframe here.
The midframe is clipped into the device at 4 points. Carefully release it and take it out once it moves easily.
Disconnect the battery
Battery Connector

Disconnect the battery using a plastic tool to prevent short circuits.
Remove SIM tray
Slide a SIM tool into the hole in the SIM tray.
Take the SIM slider out of the device.

Remove logic board
Connector

Unplug the two connectors on the lower side of the logic board.
Then first pry out the lower side of the logic board. Also unclip the logic board on the other points where it's clipped in.
Don't bend the logic board, since it breaks easily.
Insert logic board
Connector

First check if the pin for the SIM tray is in place. If not, put it back in its opening.
Place the logic board back into the device.
Make sure that the battery cable and the two connectors at the bottom don't get stuck under the board.
Slightly press in the logic board. It should snap in lightly.
Then plug in the two connectors at the bottom of the board.
Insert SIM tray
Slide the SIM tray back into the device.

If necessary, insert the SD/SIM cards first.
Connect battery
Battery Connector

Put the battery connector on its socket and press it on carefully.
Insert midframe
7 × 2.7 mm Phillips

Place the midframe back in the device and press it in.
Fasten it using the Phillips screws.
Insert speaker
4 × 2.7 mm Phillips

Place the speaker in the device and carefully press it in.
Fasten the Phillips screws.
Attach rear glass
Place the rear glass back on the device and press it on.
You can heat the rear glass again to make the glue stick better.
Test the display
Turn on your device and then drag any app across the entire screen. Drag the app once around the entire border and then in a zigzag across the screen. The app should always follow your finger.
Then test the display brightness by dragging the brightness slider to minimum and maximum.