OnePlus 2 - Replacing the earpiece

1. Turn off your device by holding down the power button until the “Power off” option appears.
2. Use your finger to confirm that you want to shut down your OnePlus 2 and wait until the screen goes blank.

1. Insert a thin, flat, tapered spudger into the gap at the corner of your smartphone. There are several clips on the outside under the back cover. You have to disconnect them by moving the spudger around the entire smartphone one time. Alternatively, you can detach the back cover using your fingernails.
2. Then you can take off the back cover.

1. You can use the SIM Tool or a paperclip to remove the SIM card tray. Press the SIM Tool into the small hole in the SIM card tray to remove it.

• 6 × Gummiabdeckung
• 18 × Phillips-Schraube

1. Remove all 18 Phillips screws that hold the plastic cover in place.
2. 6 Phillips screws are hidden under a rubber cover. Use a sharp object to lift out the cover.
3. Lift out the logic board cover. Carefully insert the pointed tip of the ESD spudger and lift the black cover. Also pry it out at other points.

You don't need to remove these parts, even-though they have been removed in the following pictures.

1. Now you can disconnect the rear camera connector. Be very careful.
2. Now lift out the old camera.

1. Now you can disconnect the front camera connector. Be very careful.
2. Now lift out the old camera.

• 1 × Phillips-Schraube

The standby button and volume buttons are attached to separate ribbon cables, which are installed onto a flat cable.

1. First you have to remove the two black sticker on the standby and display connector. You can easily pull them off with a pair of tweezers.
2. Disconnect the standby connector
3. Remove the buttons
4. Remove the cable
5. Unscrew the screw that holds the mute button. Now you can remove the braket
6. Remove the mute button

• Sensorkabel
• Displaykabel
• Antennenkabel

1. Now you can disconnect the following three connectors. Be very careful.
2. Place the pointed tip or flat end of the spudger very slightly below the contact and carefully lift it up. Make sure you don’t break off the resistors/coils that are soldered onto the logic board.

• 1 × Phillips-Schraube

Please remove the little screw close the camera connector Achte darauf, die kleine Schraube unterhab der Kamers zu entfernen.

1. Now you can carefully lift the logic board using the spudger and remove it by hand.

1. Remove the earpiece. Insert the pointed tip of the laboratory spatula or spudger below the earpiece. It’s sometimes glued firmly in place. If you still can’t detach the earpiece, you can use a heat gun to warm it slightly and soften the glue.
2. Now remove it.

• Now put the earpiece back in the appropriate position.

• 1 × Phillips-Schraube
• Antennenkabel
• Displaykabel
• Sensorkabel

1. Now put the logic board back in the frame.
2. Make sure the cables don’t get under the logic board.
3. Use the picture to check whether your logic board is positioned correctly.
4. Insert the little placeholder on the display connector.
5. Reconnect all the connectors to the logic board.

• 1 × Phillips-Schraube

1. Install the mute button.
2. Fix it with the bracket using the screw
3. Install the standby button and the volume buttons again. Use the spatula to press them into the appropriate positions.

1. Now connect the new camera.
2. Then put the adhesive strips back on.

1. Now connect the new camera.

• 18 × Phillips-Schraube
• 6 × Gummistöpsel

1. Now put the cover back on.
2. Then fasten all the Phillips screws again.
3. Don’t forget to put the little rubber plugs back in.

• Insert the sim tray

1. It’s very easy to put the back cover back on. Put it on in the correct position and press it on all the way around the phone until it’s completely clicked into place.